Propulsive Wing

The Propulsive Wing is a new patented[1] UAV (Unmanned aerial vehicle) with extremely high lift and internal volume. The Propulsive Wing is a completely new class of aircraft based on an embedded, distributed cross-flow fan propulsion system within a thick wing. The fan, partially embedded within the airfoil section, draws the flow in from the suction surface and exhausts at the trailing edge. In cruise, the combination of distributed boundary-layer ingestion and wake filling increase propulsive efficiency,[2][3] while distributed vectored thrust provides substantial improvements in pressure drag.[4]

At high angle of attack, with the fan off, the airfoil fully stalls, and a large wake is present. However, when the fan is turned on, the suction effect of the fan draws the air in, completely eliminating the wake. The result is a significant increase in lift. In addition to maintaining flight at very high angles of attack, lift and drag forces can be managed through circulation control. In particular, if the exhaust is deflected downward as it leaves the propulsor, a circulation control effect is realized. Even at low angle of attack, high lift coefficients have been shown with CFD and validated with wind tunnel experiments.[5]

The Propulsive Wing controls pitch and roll controls through vectored thrust. By distributing multiple thrust deflection flaps along the span, the high-velocity jet doubles as both the main thrust producer, as well as roll and pitch control. Collective changes in the trailing edge flaps control pitch, and spanwise differential changes control roll. Due to the circulation control effect of vectored thrust, a substantial rolling moment can be produced with very little control input.

In 2007 the cross-flow fan Propulsive Wing technology won first prize in the graduate category at the American Institute of Aeronautics and Astronautics International Student Conference.[6]

Several international groups have investigated the Propulsive Wing technology and presented their results at conferences. A group from Bauhaus Luftfahrt in Munich, Germany presented computational work demonstrating the application of the cross-flow fan Propulsive Wing for regional aircraft applications.[7] A research group from Nanjing, China built and tested a Propulsive Wing wind tunnel model, demonstrating the high lift and low drag capabilities of the design.[8]

References

  1. ↑ U.S. Patent #7,641,144
  2. ↑ Smith, Leroy H., “Wake Ingestion Propulsion Benefit,” Journal of Propulsion and Power, Vol. 9, No. 1, 1993, pp. 74-82.
  3. ↑ Kummer, Joseph D. and Dang, Thong Q., “High-Lift Propulsive Airfoil with Integrated Cross-Flow Fan,” Journal of Aircraft, Vol 43, No. 4, July–August 2006. http://pdf.aiaa.org/jaPreview/JA/2006/PVJA17610.pdf
  4. ↑ Kim, Hyun D. and Saunders, John D., “Embedded Wing Propulsion Conceptual Study,” NASA/TM-2003-212696, 2003. http://gltrs.grc.nasa.gov/reports/2003/TM-2003-212696.pdf
  5. ↑ Dygert, R. and Dang, T., “Experimental Investigation of an Embedded Crossflow Fan for Airfoil Propulsion/Circulation Control,” Journal of Propulsion and Power, Vol. 25, No. 1, Jan-Feb 2009. http://pdf.aiaa.org/jaPreview/JPP/2009/PVJA37110.pdf
  6. ↑ http://www.ecs.syr.edu/hotnews.aspx?id=185
  7. ↑ Gologan, C. et al., "Potential of the Cross-Flow Fan for Powered-Lift Regional Aircraft Applications," 9th AIAA Aviation Technology, Integration, and Operations Conference, Hilton Head, South Carolina, September 21–23, 2009. http://pdf.aiaa.org/preview/CDReadyMATIO09_2196/PV2009_7098.pdf
  8. ↑ Zhang, Yin-Hui et al., “Experimental Research of Propulsive Wing Using Cross-Flow Fan,” 3rd International Basic Research Conference on Rotorcraft Technology, Nanjing, China, October 14–16, 2009. http://www.vtol.org/nanjing2009.pdf
This article is issued from Wikipedia - version of the 1/6/2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.