Powder-actuated tool
A powder-actuated tool (often generically called a "Hilti gun" or a "Ramset gun" after their manufacturing companies) is a type of nail gun used in construction and manufacturing to join materials to hard substrates such as steel and concrete. Known as direct fastening, this technology relies on a controlled explosion created by small chemical propellant charge, similar to the process that discharges a firearm.
Powder-actuated tools come in either high velocity or low velocity types. In high velocity tools the propellant charge acts directly on the fastener. This process is similar to a firearm. Low velocity tools introduce a piston into the chamber. The propellant acts on the piston, which then drives the fastener into the substrate. (The piston is analogous to the bolt of a captive bolt pistol.) A powder-actuated tool is considered to be low velocity if the average test velocity of the fastener does not exceed 492 feet per second (150 m/s). High velocity tools may not be made or sold in the United States, however some made decades ago are still in use in shipbuilding and steel industries.
Powder-actuated fasteners are made of special heat treated steel. Common nails should never be used for powder-actuated fastenings. There are many specialized fasteners designed for specific applications in the construction and manufacturing industries.
Powder-actuated technology was developed for commercial use during the Second World War, when high velocity fastening systems were used to temporarily repair damage to ships. In the case of hull breach, these tools fastened steel plates over damaged areas.[1] These tools were developed by Mine Safety Appliances, for the United States Navy.[2] Powder-actuated tools were investigated and used prior to this development; they were used as part of submarine hunting during the First World War and were the subject of a 1921 United States patent (US Patent No. 1365869).[3]
Use
Fasteners take various forms, for example with threaded ends to use as an embedded bolt, with washers at the tips that grip softer material etc. For photos and descriptions of various fasteners see the PATMI Basic Training Manual. http://www.patmi.org/wp-content/uploads/2015/10/PATMI-Manual-2014.pdf Common nails should never be used for powder-actuated fastenings. Fasteners used in powder-actuated tools are manufactured from special steel and heat-treated to produce a very hard yet ductile fastener. Those properties are necessary for the fastener to penetrate concrete or steel without breaking.
Operation
Powder-actuated tool cartridges are specially-designed blank firearm cartridges. In many cases, the charges are ordinary firearm cartridges with modified casings, and the bullet removed. The .22 Short, developed by Smith & Wesson is common. These charges may be hand-fed, or manufactured and distributed on a plastic strip. The charges are activated when a firing pin strikes the primer, which is an explosive charge in the base of cartridge. The primer ignites the charge, which burns rapidly. The gases released by the burning of the propellant build pressure within the cartridge, which acts either on the head of the nail, or on the piston, accelerating the nail towards the muzzle.
Powder actuated tools can be variously classified:
- Direct acting (the charge acts directly on the head of the nail or high velocity), or indirect (using an intermediate piston or low velocity)
- Single-shot, or magazine-fed
- Automatic or manual piston cycling
- Automatic or manual feed of the charges
Color coding:
Color-coding for the "rounds" or "single shots" (the three shot strengths or colors typically sold to the general public are brown, green and yellow in brass):
In brass casing:
| Color coding | Velocity |
|---|---|
| Grey | 315 ft/s (96 m/s) |
| Brown | 385 ft/s (117 m/s) |
| Green | 490 ft/s (150 m/s) |
| Yellow | 575 ft/s (175 m/s) |
| Red | 675 ft/s (206 m/s) |
| Purple | 755 ft/s (230 m/s) |
In nickel (silver) casings:
| Color coding | Velocity |
|---|---|
| Grey | 845 ft/s (258 m/s) |
| Brown | 935 ft/s (285 m/s) |
| Green | 1,025 ft/s (312 m/s) |
| Yellow | 1,115 ft/s (340 m/s) |
| Red | 1,205 ft/s (367 m/s) |
| Purple | 1,295 ft/s (395 m/s) |
Not all powder-actuated tools are rated for high capacity charges — the strongest charge (nickel - purple @ 1,295 ft/s (395 m/s)), for example, is dangerous in a tool not rated for its use. Above is for a 350 grain slug from a test device.
Safety
As with their air-actuated cousins, powder-actuated guns have a muzzle safety interlock. If the muzzle is not pressed against a surface with sufficient force, the firing pin is blocked and cannot reach the load to fire it. This ensures that the gun does not discharge in an unsafe manner, causing the nail to become a projectile. Nonetheless, good judgment should always be used when using a powder-actuated nail gun, since the nail is driven with far more force than an air-actuated gun. The surface being nailed should, therefore, certainly be capable of stopping and holding the nail.
Most manufacturers of powder-actuated nail guns offer training and certification. Many projects and employers require this before an employee is permitted to use the tool.
The ownership and use of these tools is regulated in Australia. The owner has to register the tool, and an operator of one of these tools is required to have a license and to have undergone training in their use. These laws are in keeping with Australia's extremely strict firearm laws.
In the US, failure to properly dispose of charges is a common OSHA safety violation. Training is required before someone can use the tool on a jobsite.
In popular culture
- In the TV series The Wire, a real Hilti brand powder-actuated tool is pitched to the character Snoop in episode 1, season 4. The tool also features in subsequent episodes.
- In the novel trilogy The Strain by Guillermo del Toro and Chuck Hogan, modified nail guns are used by the main characters to hunt vampires. The guns are created by Professor Abraham Setrakian, who explains that he has taken ordinary, battery-operated guns and augmented them with small charges of gunpowder, in order to give them the necessary stopping power.
- The nail gun cartridges were sometimes utilized by gun enthusiasts as an ammunition for a home-made blank gun, as well as modifying an air rifle with the cartridges used as a propellant for the pellets.
See also
References
- ↑ "Engineering maintenance". Hospital Management. Clissold Publishing Co. 90: 52. 1960.
- ↑ "Powder-actuated driver". The Signalman's journal. Brotherhood of railroad signalmen of America. 29–30. 1948.
- ↑ "Powder-actuated fasteners". Engineering journal. American Institute of Steel Construction. 40–41: 99. 2003.
External links
- Ramset Powder Actuated Tool Licensing Course & Exam
- Powder Actuated Tools Operator Certification Simpson Training & Exam