Disk II

Disk II drives

The Disk II Floppy Disk Subsystem, often rendered as Disk ][, is a 5¼-inch floppy disk drive designed by Steve Wozniak and manufactured by Apple Computer. It went on sale in June 1978 at a retail price of US$495 for pre-order; it was later sold for $595 including the controller card (which can control up to two drives) and cable. The Disk II was designed specifically for use with the Apple II personal computer family to replace the slower cassette tape storage. These floppy drives cannot be used with any Macintosh computer without an Apple IIe Card as doing so will damage the drive or the controller.

Apple produced at least six variants of the basic 5¼-inch Disk II concept over the course of the Apple II series' lifetime: The Disk II, the Disk III, the DuoDisk, the Disk IIc, the UniDisk 5.25" and the Apple 5.25 Drive. While all of these drives look different and they use four different connector types, they're all electronically extremely similar, can all use the same low-level disk format, and are all interchangeable with the use of simple adapters, consisting of no more than two plugs and some wires between them. Most DuoDisk drives, the Disk IIc, the UniDisk 5.25" and the AppleDisk 5.25" even use the same 19-pin D-Sub connector, so they are directly interchangeable. The only 5.25" drive Apple sold aside from the Disk II family was a 360k MFM unit made to allow Mac IIs and SEs to read PC floppy disks.

This is not the case with Apple's 3.5" drives, which use several different disk formats and several different interfaces, electronically quite dissimilar even in models using the same connector, and are not generally interchangeable.

History

Disk II

Apple did not originally offer a disk drive for the Apple II, which used data cassette storage like other microcomputers of the time. Mike Markkula asked fellow cofounder Steve Wozniak to design a drive system for the computer after finding that a checkbook-balancing program Markkula had written took too long to load from tape.[1] Wozniak knew nothing about disk controllers, but while at Hewlett-Packard had designed a simple, five-chip circuit to operate a Shugart Associates drive. Wozniak began studying existing floppy controllers, including North Star and IBM models. Standard floppy controller boards were large devices that used dozens of TTL chips. In addition to being expensive, they were also much too big to fit into the Apple II's small case. Initially, Wozniak attempted to develop an FM-type controller with a smaller chip count and by making improvements to the FM encoding scheme, he was able to squeeze out 10 sector per track storage. However, he soon decided he could do even better and switched to another, completely different encoding method known as "GCR" (Group Code Recording) which was a modified version of recording schemes used on tape storage. This allowed still more storage, up to 13 sectors per track. Wozniak called the resultant Disk II system "my most incredible experience at Apple and the finest job I did", and credited it and VisiCalc with the Apple II's success.[2] The Disk II was a veritable coup d'éclat for Apple, being the cheapest floppy disk system ever sold up to that point and immensely profitable for the company, in addition to having nearly 20% more storage space than standard FM drives. For a while, the only direct competitor in the microcomputer industry was the TRS-80 Model I, which offered disk drives only as an extra-cost option, and which had used only standard FM storage for a mere 85k.[3] However, the advantage of Wozniak's design was somewhat nullified when the cost of double-density MFM controllers dropped only a year after the Disk II's introduction.

The Apple II's lack of a disk drive was "a glaring weakness" in what was otherwise intended to be a polished, professional product. Speaking later, Osborne I designer Lee Felsenstein stated, "The difference between cassette and disk systems was the difference between hobbyist devices and a computer. You couldn't have expected, say, VisiCalc, to run on a cassette system." Recognizing that the II needed a disk drive to be taken seriously, Apple set out to develop a disk drive and a DOS to run it. Wozniak spent the 1977 Christmas holidays adapting his controller design, which reduced the number of chips used by a factor of 10 compared to existing controllers. Still lacking a DOS, and with Wozniak inexperienced in operating system design, Jobs approached Shepardson Microsystems with the project. On April 10, 1978 Apple signed a contract for $13,000 with Sheperdson to develop the DOS.[4]

The initial Disk II drives (A2M0003) were modifications of the Shugart SA-400, which was the first commercially available 5.25" diskette drive. Apple purchased only the bare drive mechanisms without the standard SA-400 controller board, replaced it with Wozniak's board design, and then stamped the Apple rainbow logo onto the faceplate. Early production at Apple was handled by two people, and they assembled 30 drives a day. By 1982, Apple switched to Alps drives for cost reasons.[5][6]

Shortly after the disk drive project began in late 1977, Steve Jobs made several trips to Shugart's offices announcing that he wanted a disk drive that would cost just $100. After Wozniak finished studying IBM disk controller designs, Jobs then demanded that Shugart sell them a stripped disk drive that had no controller board, index sensor, load solenoids, or track zero sensor. Although puzzled by this request, Shugart complied and provided Apple with 25 drive mechanisms that they could use as prototypes in developing a disk system for the Apple II. The prototypes received the designation of SA-390.

Steve Wozniak found out that some of the SA-390 drives didn't work without adjustments while others simply wouldn't work at all. Fellow engineer Cliff Huston came up with several procedures for adjusting the drives on the assembly line. When Apple sent an order into Shugart for more SA-390s, a Shugart engineer admitted that the disk drive manufacturer had been scamming Apple and that the SA-390s were actually reject SA-400s that failed to pass factory inspection. The idea was that Apple couldn't get the drives to work and would be forced to go back and purchase more expensive SA-400s.

Normal storage capacity per disk side was 113.75 KiB with Apple DOS 3.2.1 and earlier (256 bytes per sector, 13 sectors per track, 35 tracks per side), or 140 KiB with DOS 3.3 and all later Apple II operating systems, and the accompanying ROM update for the controller card (16 sectors per track). The 16-sector upgrade was introduced in 1980, it modified only the software and the controller card firmware to use a more efficient GCR code. Neither the drive itself, nor the controller logic, nor the physical bit density was changed.

Since the Disk II controller was completely software-operated, the user had total control over the encoding and format so long as it was within the physical limits of the drive mechanism and media. Microsoft introduced a CP/M card for the Apple II in 1980 and because of this ability, it was possible for users to read any 5.25" single sided CP/M-formatted floppy disks (including Osborne, Kaypro, and Morrow) despite them using FM/MFM instead of the Apple's standard GCR format. This also allowed software companies to use all sorts of ingenious copy protection schemes.

The Shugart SA-400 that the Disk II was adapted from was a single-sided, 35-track drive. However, it was common for users to manually flip the disk to utilize the opposite side, after cutting a second notch on the diskette's protective shell to allow write-access. Most commercial software using more than one disk side was shipped on such "flippy" disks as well. Only one side could be accessed at once, but it did essentially double the capacity of each floppy diskette, an important consideration especially in the early years when media was still quite expensive.

In the Disk II, the full-height drive mechanism shipped inside a beige painted metal case and connected to the controller card via a 20-pin ribbon cable; the controller card was plugged into one of the bus slots on the Apple's mainboard. The connector is very easy to misalign on the controller card, which will short out a certain IC in the drive; if later connected correctly, a drive damaged this way will delete any disk inserted into it as soon as it starts spinning, even write-protected disks such as those used to distribute commercial software. This problem resulted in numerous customer complaints and repairs, which led to Apple printing warning messages in their user's manuals to explain how to properly install the connector. They used different connectors that could not be misaligned in later drives. DB-19 adapters for the original Disk II were eventually available for use with Apple's later connector standard.

Up to 14 drives could be attached to one Apple II or Apple IIe computer - two drives per controller card, one card per slot, and there were seven usable slots per computer. While the DOS and ProDOS operating systems worked equally well with the card in any of the normal slots (i.e. all except slot 0 of the Apple II/II+ or the special memory expansion slots of the later models), Apple's printed manuals suggested using slot 6 for the first controller card; most Apple II software expects this slot to be used for the main 5.25" disk drive and fails otherwise. A Bell & Howell version of the Disk II was also manufactured by Apple in a black painted case, which matched the color of the Bell & Howell version of the Apple II Plus, which Apple was already manufacturing.

Disk III

In 1978, Apple intended to develop its own "FileWare" drive mechanism for use in the new Apple /// and Lisa business computers then being developed. They quickly ran into difficulties with the mechanisms, which precluded them from being incorporated in the Apple ///. That machine thus continued to use the same Shugart design as the Disk II.[7]

The first variation of the Disk II introduced for the Apple ///, called the Disk III (A3M0004), used the identical drive mechanism inside a modified plastic case with a proprietary connector. With some modification both drives are interchangeable. Though Apple sought to force the purchase of new drives with the Apple ///, many former Apple II users quickly devised a way to adapt their existing and cheaper Disk II drives, however only one external Disk II was supported in this manner. The Disk III was the first to allow daisy chaining of up to three additional drives to the single 26-pin ribbon cable connector on the Apple ///, for a total of 4 floppy disk drives – the Apple /// was the first Apple to contain a built-in drive mechanism. The Apple III Plus changed its 26-pin connector to a DB-25 connector, which required an adapter for use with the Disk III.

FileWare

In 1983, Apple finally announced a single and dual external drive (UniFile and DuoFile) implementing the 871K "FileWare" mechanism used in the original Apple Lisa, as a replacement for the Disk II & /// drives. However, due to the reliability problems of the Apple-built "Twiggy" drive mechanisms, the products never shipped.[8][9]

DuoDisk

In 1983, along with the introduction of the Apple IIe, Apple initially offered a combination of two, two third-height, 140ki Disk II drive mechanisms side-by-side in a single plastic case, called the DuoDisk 5.25 (A9M0108), which could not be daisy-chained. The unit was designed to be stacked on top of the computer, and beneath the monitor. Each unit required its own disk controller card (as each card could still control only two drives) and the number of units was thus limited to the number of available slots; in practice, few uses of the Apple II computer can make good use of more than two 5.25" drives, so this limitation mattered little. Originally released with a DB-25 connector, to match that of the Apple III Plus, it was the first to adopt Apple's standard DB-19 floppy drive connector.

Disk IIc

Disk IIc drive.

The Disk IIc (A2M4050) was a half-height 5.25-inch floppy disk drive introduced by Apple Computer in 1984 styled for use alongside the Apple IIc personal computer, the only Apple II to contain a built-in disk drive mechanism. The disk port on the original IIc was only designed to control one additional, external 5.25-inch disk drive, and as such, this particular drive omitted a daisy-chain port in back. It was possible to use it on other Apple II models, so long as it came last in the chain of drive devices (due to lacking a daisy-chain port); but since the Disk IIc was sold without a controller card, the Apple IIc computer needing none, it had to be adapted to an existing Disk II controller card in this case. Essentially the same as the full-height Disk II, it offered slightly faster access time (which didn't help unless software was specifically written to make use of it; most wasn't). Apple sold the Disk IIc for US$329, and other companies later sold similar drives for less.[10]

3.5"

In 1984, Apple had opted for the more modern, Sony-designed 3.5" floppy disk in late-model Lisas and the new Apple Macintosh. Accordingly, they attempted to introduce a new 3.5" 800k floppy disk format for the Apple II series as well, to eventually replace the 140k Disk II format. However, the external UniDisk 3.5 drive required a ROM upgrade (for existing Apple IIc machines; new ones shipped after this time had it from the factory) or a new kind of disk controller card (the so-called "Liron Card", for the Apple IIe) to be used. The much larger capacity and higher bitrate of the 3.5" drives made it impractical to use the software-driven Disk II controller because the 1Mhz 6502 CPU in the Apple II line was too slow to be able to read them. Thus a new and much more advanced (and correspondingly expensive) hardware floppy controller had to be used. And many original Apple IIs could not use the new controller card at all without further upgrades. Also, almost all commercial software for the Apple II series continued to be published on 5.25" disks which had a much larger installed base. All of these reasons added up to one thing: the 3.5" format was not widely accepted by Apple II users. The Apple 3.5 Drive used the same 800k format as the UniDisk 3.5", but it did away with the internal computer, which made it cheaper. Unlike all earlier Apple II drives, it was designed to work with the Macintosh too, and among Apple II models, it was compatible only with the Apple IIGS and the Apple IIc+ models, which both had a faster main CPU. On the Apple IIGS, whose improved audiovisual capacities really demanded a higher-capacity disk format as well, the 3.5" format was accepted by users and became the standard format. Though Apple eventually offered a 1.44MB Superdrive with matching controller card for the Apple II series as well, the 5.25" Disk II format drives continued to be offered alongside the newer 3.5" drives and remained the standard on the non-IIgs models until the platform was discontinued in 1993.

Officially, the following 3.5" drives could be used on the Apple II:

The 400k and 800k Macintosh external drives (M0130 and M0131) are incompatible with standard Apple II controllers as they do not support their automatic disk eject feature, although they could be used with third-party controllers.

UniDisk 5.25" and Apple 5.25 Drive

Along with the UniDisk 3.5", Apple introduced the UniDisk 5.25 (A9M0104) in a plastic case, which modernized the appearance of the Disk II to better match the Apple IIe. Since the UniDisk 5.25" could fully replace the Disk II in all its uses, the original Disk II was canceled at this point. This was followed in 1986 by a Platinum-gray version which was renamed Apple 5.25 Drive (A9M0107), companion to the Apple 3.5 Drive, and introduced alongside the first Platinum-colored computer, the Apple IIGS. Essentially these were both single half-height Disk II mechanisms inside an individual drive enclosure, just like the Disk IIc had been. All of these drives introduced a daisy chain pass-through port. While the drives are essentially interchangeable among Apple II computers, both with each other and with the earlier drives, only the Apple 5.25 Drive can be used with the Apple IIe Card on a Macintosh LC.

Apple PC 5.25" Drive

There is one 5.25 inch drive made by Apple that is completely incompatible with all the drives named above. In 1987 Apple sought to better compete in the IBM dominated business market by offering a means of cross-compatibility. Alongside the release of the Macintosh SE & Macintosh II, Apple released the Apple PC 5.25" Drive which required a separate custom PC 5.25 Floppy Disk Controller Card, different for each Mac model. It is the only 5.25" drive manufactured by Apple that can be used by the Macintosh. This drive was for use with industry standard double-sided 5.25" 360K formatted flexible disks. It was similar in appearance to the Disk IIc. Through the use of a special Macintosh Apple File Exchange utility shipped with it, the drive could read files from, and write files to, floppy disks in MS-DOS formats. Software "translators" could convert documents between WordStar and MacWrite, among others.[11] Unfortunately, this drive is not just incompatible with all Apple II computers, but also with the Apple IIe Card for the Macintosh LC; it cannot be used to allow a Macintosh to read from or write to 5.25" Apple II formatted disks either.

This drive was made obsolete by the industry-wide adoption of 3.5" disks and was replaced by the 3.5" Apple FDHD Drive, which could not only read and write all then-existing native Macintosh, DOS and Windows formats, but the Apple II ProDOS format as well.

Disk II Cable Pinout

This table shows the pinout of the original 1979 Disk II controller and newer 1983 Uni/Duo Disk I/O controller (655-0101).

The circuitry of these two controllers are identical. The Disk II header pin numbering is per the Disk II controller card silkscreen and the circuit schematic given in the DOS 3.3 manual. The Uni/Duo Disk D-19 pinout is taken from the Apple //c Reference Manual, Volume 1.[12]

Disk II Header PinDuoDisk/Disk IIc/UniDisk/Apple Disk D-19 PinDuoDisk/UniDisk/Apple Disk Controller Card Cable ColorSignal NameDescription
1,3,5,71,2,3,4Brown,Orange,Green,VioletGNDGround reference and supply
211RedSEEKPH0Phase 0 stepper motor signal
412YellowSEEKPH1Phase 1 stepper motor signal
613BlueSEEKPH2Phase 2 stepper motor signal
814GreySEEKPH3Phase 3 stepper motor signal
95White-12V-12 volt supply
1015BlackWRREQ*Write request signal
11,126,16Brown,Red+5V+5 volt supply
13,15,17,197,8Orange,Green+12V+12 volt supply
1417YellowDR2* (ENABLE*)Drive 2 select/Drive enable signal
1618BlueRDDATARead data signal
1819GreyWRDATAWrite data signal
2010WhiteWRPROTWrite protect signal
x9VioletEXINT*External interrupt

NOTES:

See also

References

  1. ↑ Markoff, John (September 1, 1997). "An 'Unknown' Co-Founder Leaves After 20 Years of Glory and Turmoil". The New York Times. Retrieved February 4, 2011.
  2. ↑ Williams, Gregg; Moore, Rob (January 1985). "The Apple Story / Part 2: More History and the Apple III". BYTE (interview). p. 166. Retrieved October 26, 2013.
  3. ↑ McMullen, Barbara E.; John F. (1984-02-21). "Apple Charts The Course For IBM". PC Magazine. p. 122. Retrieved 24 October 2013.
  4. ↑ http://www.cnet.com/news/the-untold-story-behind-apples-13000-operating-system/
  5. ↑ "A.P.P.L.E. Co-op Celebrates A Decade of Service", Call-A.P.P.L.E., Feb 1988: 12-27.
  6. ↑ "Apple and Apple II History", The Apple II Guide, Cupertino, CA, Apple Computer, Inc., Fall 1990: 9-16.
  7. ↑ Apple and the Floppy Drive Archived May 6, 2007, at the Wayback Machine.
  8. ↑ "Apple's Twiggy Disks". Brouhaha.com. January 2, 1999. Retrieved August 20, 2010.
  9. ↑ "Lisa2". Apple2world.jp. Retrieved August 20, 2010.
  10. ↑ Baum, Peter. "Expanding The Unexpandable IIc", Softalk, Jun 1984: 95-97.
  11. ↑ Apple PC 5.25 Drive: Description at Apple.com
  12. ↑ The Apple //c Reference Manual, Volume 1, Cupertino, CA, Apple Computer, Inc., 1984: pp. 252-253.
This article is issued from Wikipedia - version of the 11/23/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.