British Association screw threads

British Association or BA screw threads are a largely obsolete set of small screw threads, the largest being 0BA at 6 mm diameter. They were, and to some extent still are, used for miniature instruments and modelling.

They are unusual in that they were probably the most "scientific" design of screw, starting with 0BA at 6.0mm diameter and 1.0mm pitch and progressing in a geometric sequence where each larger number was 0.9 times the pitch of the last size. They then spoiled this by rounding to 2 significant figures in metric and then converting to inches and rounding to the thousandth of an inch. This anticipated worldwide metrication by about a century. The design was first proposed by the British Association in 1884[1][2] with a thread angle and depth based on the Swiss Thury thread,[3] it was adopted by the Association in 1903.

The Thury thread was different in that it went both positive and negative all the way up to a size of -20 which was 75.2mm diameter by 8.23mm pitch. The Thury numbers were rounded to three significant figures. The Thury thread form had the crests rounded at 1/6p and the roots rounded at 1/5p so the thread angle was close to 47.5 degrees but not exactly. This was simplified in the BA thread definition by defining the thread angle to be 47.5 degrees exactly and the thread form to be symmetrical with a depth of 0.6p.

The British Standards Institution recommends the use of BA sizes in place of the smaller British Standard Whitworth (BSW) and British Standard Fine (BSF) thread screws (those below 1/4").[4]:4 Generally, the 0BA size was dropped in place of 7/32" BSF in assemblies that included larger fasteners, however, in smaller equipment that was primarily electronic/electrical the 0BA size would typically be used in place of the BSF or BSW screw where it was the largest size required.

BA threads are still used in some precision instruments, such as optics and moving-coil meters, relays etc. A 2BA thread is used to connect the head of a dart to its shaft — as such, it is one of the few common uses of this thread in North America.

2BA threads are commonly found in the old imperial BESA (British Engineering Standards Association) conduit boxes in the UK which are still in use (but not installed) today.

BA thread sizes

The pitch of 0BA is 1 mm and the pitch of each higher numbered thread is obtained by multiplying the pitch of the lower number by 0.9 so K-BA has a pitch of [4]:12 rounded to two significant figures in mm. The major diameter is given by ,[4]:12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter.

BA sizes are specified by the following British Standards:

The angle of the thread is 47.5 degrees[4]:2 and the depth of thread is 0.6 times the pitch with rounded tops and bottoms. Thus the shortening at the crest and root is given by 0.26817p with a radius of 0.18083p at both crest and root.[4]:2 The 1884 report specifies a radius of 2/11p (0.181818p) but this was an approximation to the correct value.

The pitch diameter of the thread is simply OD - 0.6p and the minor diameter is OD - 1.2p.

The thread angle is different from that used by Whitworth (55 degrees), US Unified threads (60 degrees) and ISO Metric (60 degrees) so BA fasteners are not properly interchangeable with Whitworth or metric ones even when the pitch and diameter are similar enough that they can be screwed together (e.g., although 0BA appears similar to M6x1mm, the male and female surfaces do not mate properly for bearing a load). Standard BA sizes are defined between 0BA and 22BA. The even sizes are much more common and the very small sizes are not used very often and other standards tend to be used (e.g., NHS).

BA Pitch OD Threads per inch OD Spanner Spanner
(mm) (mm) (in) (mm) (in)
0 1.00 6.00 25.40 0.2362 10.5000 0.4134
1 0.90 5.30 28.22 0.2087 9.2750 0.3652
2 0.81 4.70 31.36 0.1850 8.2250 0.3238
3 0.73 4.10 34.79 0.1614 7.1750 0.2825
4 0.66 3.60 38.48 0.1417 6.3000 0.2480
5 0.59 3.20 43.05 0.1260 5.6000 0.2205
6 0.53 2.80 47.92 0.1102 4.9000 0.1929
7 0.48 2.50 52.92 0.0984 4.3750 0.1722
8 0.43 2.20 59.07 0.0866 3.8500 0.1516
9 0.39 1.90 65.13 0.0748 3.3250 0.1309
10 0.35 1.70 72.57 0.0669 2.9750 0.1171
etc
25 0.072 0.25 352.78 0.0098 0.4375 0.0172

Notes

  1. ↑ "First Report of the BA Committee on small screws". sizes.com. Retrieved 2016-07-23.
  2. ↑ "Second Report of the British Association for the Advancement of Science's Small Screws Committee, 1884.". sizes.com. Retrieved 2016-07-23.
  3. ↑ "Thury Thread". sizes.com. Retrieved 2016-07-23.
  4. 1 2 3 4 5 British Standards Institution. British Association (B.A.) screw threads – requirements. ISBN 978-0-580-60893-3. BS 93:2008.

External links

This article is issued from Wikipedia - version of the 11/8/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.